Bolt from 1987 removed in 2015. <br> It pulled out under about a 50 lb load. <br>

Gregger Man > ACE

Bolt from 1987 removed in 2015. <br>
It pulled out under about a 50 lb load.<br>

ID 110767446 ·

Flag This Photo

· Copyright Violation?

Apple Strudel before - welded cold shuts, carbon steel bolts, permanent cordelette.

Tree atop P2 of Point Break. I cut off 7 ratty slings.

Rate Photo

0.0 from 0 votes

Gregger Man

Jul 18, 2015

“Bolt from 1987 removed in 2015.
It pulled out under about a 50 lb load.
”

0 Comments

Nearby Photos

Doodad tools. Latest improvement to the spinner tool: use a 1/4" steel rivet for the stop pin. A piece of bicycle tube keeps it in place if you need to reverse the drill off the stud (the previous pin could go flying.)

The DragonCam that had been stuck for a while at the lip on the final pitch of Vertigo.<br>
Still good. Put it on your Indian Creek rack.

Improved P3 anchor - Removed a huge pile of wedged tat (had to use a funkness device to get each piece out of the crack.) Replaced it with a climbing rope inside a 1" tubular webbing sheath tied in two loops. The first loop has its own forged ring and is tied with a water knot. The tails of that loop go around again with another forged ring and end in a double fisherman's knot. The webbing should protect from UV for a long while and keep more tat from appearing.

New anchor for Atom Smasher.

New 1/2" SS anchors for Sunrider

Rusty 3/8" anchors removed from Sunrider

Hardware removed from 'Laughing at the Moon', replaced with 1/2" stainless.

Wind Tower middle ledge near 'Left Out' after the trundle/sweeping.

Bolts from Quadrille and Toys for Tots. The Toys lead bolt came out with maybe a couple hundred pounds of axial force. The second lead bolt was so bent and abused that I could only funk on it and it broke.

Bolt spinner tool with 1/4" pin instead of a jam nut.<br>

Apple Strudel upgrade

Crux bolt removed from Apple Strudel.

Pins from Werk Supp

New Vertigo rap anchor

New bolts above P2 of Ruper/Rover. Replaced old Metolius fat hangers and 3" x 3/8" carbon steel with new SS 4.75" x 1/2" and SS double ring hangers.

painted bolts

Old Metolius design from the '80s and an 8mm allen head drop-in bolt.

Apple Strudel before - welded cold shuts, carbon steel bolts, permanent cordelette.

Bolt from 1987 removed in 2015. <br>
It pulled out under about a 50 lb load.<br>

Tree atop P2 of Point Break. I cut off 7 ratty slings.

Retirement party for some more rusty-crusty mank. Bolts from Point Break and Prince of Darkness.

New anchor at the summit of Point Break that replaces the dead tree. Rappel either direction - down the route or down to the base of Gambit where the trail is nicely maintained.

Replaced first bolt on P2. Plan to get the second some time soon.

FHRC pin evaluation flow chart

New anchor beside the slim P2 tree on Point Break.

C'est la Vie top anchor before

ACE t-shirt

C'est la Vie top anchor after upgrade

Pin from Quadrille. Note where it was in contact with the rock...

1st lead bolt from P1 of C'est la Vie. Replaced 1/25/2015 by a 1/2" SS bolt in the same hole.

#3 that had been stuck on P2 of Gambit for several years. Took some hard persuasion to remove it.

Wind Tower middle ledge near 'Left Out' before the trundle/sweeping.