Mountain Project Logo
Climb
MTB
Hike
Trailrun
Ski

Gregger Man > ACE

Work for ACE
Wind Tower middle ledge near 'Left Out' before the trundle/sweeping.
Wind Tower middle ledge near 'Left Out' before…
 0
Wind Tower middle ledge near 'Left Out' after the trundle/sweeping.
Wind Tower middle ledge near 'Left Out' after t…
 0
FHRC pin evaluation flow chart
FHRC pin evaluation flow chart
 0
Rusty 3/8" anchors removed from Sunrider
Rusty 3/8" anchors removed from Sunrider
 2
New 1/2" SS anchors for Sunrider
New 1/2" SS anchors for Sunrider
 1
painted bolts
painted bolts
 0
New bolts above P2 of Ruper/Rover. Replaced old Metolius fat hangers and 3" x 3/8" carbon steel with new SS 4.75" x 1/2" and SS double ring hangers.
New bolts above P2 of Ruper/Rover. Replaced old…
 0
New Vertigo rap anchor
New Vertigo rap anchor
 0
Pins from Werk Supp
Pins from Werk Supp
 0
Crux bolt removed from Apple Strudel.
Crux bolt removed from Apple Strudel.
 0
Apple Strudel upgrade
Apple Strudel upgrade
 0
Apple Strudel before - welded cold shuts, carbon steel bolts, permanent cordelette.
Apple Strudel before - welded cold shuts, carbo…
 0
Replaced first bolt on P2. Plan to get the second some time soon.
Replaced first bolt on P2. Plan to get the seco…
 0
C'est la Vie top anchor before
C'est la Vie top anchor before
 0
C'est la Vie top anchor after upgrade
C'est la Vie top anchor after upgrade
 0
1st lead bolt from P1 of C'est la Vie. Replaced 1/25/2015 by a 1/2" SS bolt in the same hole.
1st lead bolt from P1 of C'est la Vie. Replaced…
 0
The DragonCam that had been stuck for a while at the lip on the final pitch of Vertigo.<br> Still good. Put it on your Indian Creek rack.
The DragonCam that had been stuck for a while a…
 2
Hardware removed from 'Laughing at the Moon', replaced with 1/2" stainless.
Hardware removed from 'Laughing at the Moon', r…
 0
Old Metolius design from the '80s and an 8mm allen head drop-in bolt.
Old Metolius design from the '80s and an 8mm al…
 0
Bolt from 1987 removed in 2015. <br> It pulled out under about a 50 lb load.<br>
Bolt from 1987 removed in 2015. It pulled out…
 0
New anchor for Atom Smasher.
New anchor for Atom Smasher.
 1
Retirement party for some more rusty-crusty mank. Bolts from Point Break and Prince of Darkness.
Retirement party for some more rusty-crusty man…
 0
Bolt spinner tool with 1/4" pin instead of a jam nut.<br>
Bolt spinner tool with 1/4" pin instead of a ja…
 0
Doodad tools. Latest improvement to the spinner tool: use a 1/4" steel rivet for the stop pin. A piece of bicycle tube keeps it in place if you need to reverse the drill off the stud (the previous pin could go flying.)
Doodad tools. Latest improvement to the spinner…
 1
Tree atop P2 of Point Break. I cut off 7 ratty slings.
Tree atop P2 of Point Break. I cut off 7 ratty…
 0
New anchor beside the slim P2 tree on Point Break.
New anchor beside the slim P2 tree on Point Break.
 0
New anchor at the summit of Point Break that replaces the dead tree. Rappel either direction - down the route or down to the base of Gambit where the trail is nicely maintained.
New anchor at the summit of Point Break that re…
 0
ACE t-shirt
ACE t-shirt
 0
Bolts from Quadrille and Toys for Tots. The Toys lead bolt came out with maybe a couple hundred pounds of axial force. The second lead bolt was so bent and abused that I could only funk on it and it broke.
Bolts from Quadrille and Toys for Tots. The Toy…
 0
Pin from Quadrille. Note where it was in contact with the rock...
Pin from Quadrille. Note where it was in contac…
 0
Improved P3 anchor - Removed a huge pile of wedged tat (had to use a funkness device to get each piece out of the crack.) Replaced it with a climbing rope inside a 1" tubular webbing sheath tied in two loops. The first loop has its own forged ring and is tied with a water knot. The tails of that loop go around again with another forged ring and end in a double fisherman's knot. The webbing should protect from UV for a long while and keep more tat from appearing.
Improved P3 anchor - Removed a huge pile of wed…
 1
#3 that had been stuck on P2 of Gambit for several years. Took some hard persuasion to remove it.
#3 that had been stuck on P2 of Gambit for seve…
 0
The cam removed from Variation to Mail Ridge.
The cam removed from Variation to Mail Ridge.
 0
Toproping thru single-ring hangers is more likely to wear them unevenly
Toproping thru single-ring hangers is more like…
 0
Welcome

Join the Community! It's FREE

Already have an account? Login to close this notice.

Get Started