MichaelChad's Posts and Comments on Mountain Project

MichaelChad

Broken Arrow, OK

46 years old · Male

Ignore User

More About MichaelChad Drop down

Member Since

Aug 13, 2015

Last Visit: Sep 27, 2017

20 Points
Point Rank: #26,937 Details Drop down

0 Areas

0 pts - 15 each

0 Routes

0 pts - 10 each

4 Photos

20 pts - 5 each

0 Approach Trails

0 pts - 4 each

0 Page Improvements

0 pts - 1 each

MichaelChad is in the Partner Finder
Best Times to Meet: Weekday/evenings, weekends anytime

Likes Trad, Gym

	Leads	Follows
Trad	5.7	5.9
Boulders	V0

More Info

Just getting started, excited to be a part of what looks like a very active community!

Comments

None yet.

Forum Messages View All 8

Gear > Climbing Gear Discussion Reply: stinky climbing shoe fix Nov 22, 2015 I keep one of these (kiwi shoe freshener) in my truck, works awesome. Turn the top, poke it inside the shoe, done. Once a week has kept all the stench away. I even let it go… View Message
General > Beginning Climbers Reply: Nut tool tethers? Nov 18, 2015 Thanks, but I think there were some thoughtful and valid views after it, including yours. To be fair, I use a harness with an extra ice tool carrier loop between the front… View Message
General > Beginning Climbers Reply: Nut tool tethers? Nov 15, 2015 I use a universal auto shutoff tether from a boat/jet ski. The coils are bigger, don't twist into knots when you extend/retract, can go more than full arm length, and barely h… View Message
Gear > Climbing Gear Discussion Reply: Broken trigger bar on camalot Nov 9, 2015 It's most likely ABS, or ABS based. You can test by putting a dab of MEK, Toluene, or even acetone I think (nail polish remover) in an inconspicuous area and see if it pulls u… View Message
Gear > Climbing Gear Discussion Reply: Broken trigger bar on camalot Nov 9, 2015 Yup. Good, nasty stuff (think solvent). Works great for creating bonds between certain synthetic materials, acrylic, ABS etc... And breaking bonds like certain adhesives. Y… View Message
Gear > Climbing Gear Discussion Reply: Broken trigger bar on camalot Nov 6, 2015 If it's ABS based and a clean crack you can use MEK in the seam and hold it together till the MEK evaporates. Bond will be stronger than any glue. Just apply lightly with a q… View Message

Route Scores View All 8

5.9+ 5c 17 VI 17 E1 5a 7 ● Jellybean Limeade (link-up) Sport, TR Tulsa Area > … > Lost City Area > Lost City
5.8 5b 16 VI- 15 HVS 4c V1 5 28 ● Jackarete Sport, TR, Boulder Tulsa Area > … > Lost City Area > Lost City
5.9 5c 17 VI 17 HVS 5a 34 ● Zig Zag Sport, TR Tulsa Area > … > Lost City Area > John's Wall
V4 6B 15 ● Ordeal Boulder Tulsa Area > … > Autobahn Area (… > Cub Scout Wall
5.9- 5c 17 VI 16 HVS 4c 9 ● Crack Right (AKA Accent Classic… Trad Tulsa Area > … > Lost City Area > John's Wall
5.7 5a 15 V+ 13 MVS 4b 11 ● Crack Left (AKA Accent Classic Two) Trad, TR Tulsa Area > … > Lost City Area > John's Wall