Mountain Project Logo

Ugly Hardware Only

Kyle McPheeters · · Chattanooga, TN · Joined Nov 2013 · Points: 1

Dont get me wrong, would still whip...

timothy fisher · · CHARLOTTE · Joined Nov 2017 · Points: 35

The welded 1/2" shut was as least as strong as the bolt when they were new. Great to see you upgrade these Anna!

Anna Brown · · Albuquerque, NM · Joined Mar 2015 · Points: 9,761

This cold shut was on a single pitch anchor where one of the bolts had already been upgraded but not this second one. It was my first cold shut upgrade and it’s less “ugly” than just “older”. Time to update it so no one has to question if they’d whip or not. We replaced 8 anchors out of about 20 on this wall. Several of the anchors were washer stacks with rusted chain.

Salamanizer Ski · · Off the Grid… · Joined Sep 2005 · Points: 24,464

Definitely justified in replacing that old thing Anna. Keep up the good work. Love seeing that old mank. 

Adam W · · TX/Nevada · Joined Dec 2019 · Points: 532

I know who did it and told them it belonged in this thread:

Anna Brown · · Albuquerque, NM · Joined Mar 2015 · Points: 9,761

Holy blue!!! I’ve never seen such an anchor. It’s creative, I’ll say that.

Thank you, Salamanizer Ski! I don’t like manky anchors and there’s nothing I enjoy better than upgrading them. 

timothy fisher · · CHARLOTTE · Joined Nov 2017 · Points: 35

I am not so sure the "Holy Blue" qualifies as Ugly. For an arid location that it is acceptable to use carbon steel wear points. That portion can be upgraded with basic tools. As long as the rope does not get pinched against the rock. 

I wont use carbon steel here in the mid atlantic(including mussies). In many cases it will rust to shit long before it wears out.

Adam W · · TX/Nevada · Joined Dec 2019 · Points: 532

It was already changed to stainless chain, this was some weirdness used with a fixed line during development underneath

Mr Rogers · · Pollock Pines and Bay area CA · Joined Aug 2010 · Points: 92
Adam W wrote:

I know who did it and told them it belonged in this thread:

Material lifting pear. Nice.
Only issue I see is those shackles are not moused. However, I would have just linked the right shackle into the left shackle and used the left lower shackle as the thread/lower point.
Dude a crane OP or ground rigger??

Adam W · · TX/Nevada · Joined Dec 2019 · Points: 532

It came from some sort of convention center rigging job.

Matt Wetmore · · Lost Wages, NV · Joined May 2017 · Points: 565

Bolts for a handline, the one driven into the crack wiggles.

Ben V · · Central Maine · Joined Nov 2016 · Points: 2,281

Good riddance! Some of these cold shuts came out with just the claw of a framing hammer. 

Anna Brown · · Albuquerque, NM · Joined Mar 2015 · Points: 9,761

Great haul Ben!!

Big Red · · Seattle · Joined Apr 2013 · Points: 1,254

Great job everyone, all these photos are inspiring me to go back out and collect some more mank.

Anna Brown · · Albuquerque, NM · Joined Mar 2015 · Points: 9,761

Big Red, Here’s some more inspiration. 

Tal M · · Denver, CO · Joined Dec 2018 · Points: 6,886

Some classic late 90s/early 00s stainless hanger/plated bolt corrosion

And a little before/after on the same route. Never seen these Trango hangers in the wild before

Mikey Schaefer · · Reno, NV · Joined Jun 2014 · Points: 233
Anna Brown wrote:

Big Red, Here’s some more inspiration. 

Am I missing some reference?  Isn’t this considered totally bomber and far from need of replacement?

timothy fisher · · CHARLOTTE · Joined Nov 2017 · Points: 35
Mikey Schaefer wrote:

Am I missing some reference?  Isn’t this considered totally bomber and far from need of replacement?

Maybe the tangle of carbon steel chain is what Anna was focused on.

Anna Brown · · Albuquerque, NM · Joined Mar 2015 · Points: 9,761

Mikey,
The mussy in the photo I posted didn't have sharp edges yet. Is that the measure for when it should be replaced or is there an official thickness measure? 

I had an extra new mussy with me at the wall so we replaced this one since it was clearly heavily worn. To me, the challenge with worn lowering hardware is some climbers see a worn groove and report the hardware as ready for replacement. The mussy in the photo was on a popular route but it was less worn than the one I was actually there to replace because of a report. Since there isn't a formal way to report worn hardware in my area (and so few people actually report it when it is worn), I'm okay replacing lowering hardware that is this worn when I have the hardware and I'm at the wall. I personally don't want to go back to check it if someone reports it again in a year and what if it's sharp in a year and it doesn't get checked?!

Brian in SLC · · Sandy, UT · Joined Oct 2003 · Points: 23,021

Some interesting mussy hook tests from the hownot2 guys:


I think if the wear point is still thicker than the eye loop at the top...super good enough (as those guys say).

This topic is locked and closed to new replies.

Log In to Reply
Welcome

Join the Community! It's FREE

Already have an account? Login to close this notice.