Mountain Project Logo

Recovering alpine draws that deploy smoothly

Original Post
Michael Wolfe · · Madison, WI · Joined Oct 2021 · Points: 326

Brand new slings in alpine draws typically deploy more smoothly than older slings. Eventually overtime, the slings becomes fuzzy and tacky. As a result, we inevitably deal with alpine draws that tangle up when we try to extend a placement; not fun when you're pressed on the sharp end. 

My understanding is there is some coating on a factory-fresh sling that keeps it smooth. The coating wears off eventually and the sling becomes annoyingly tacky. In my experience, this happens well before the sling "ages out" and needs to be retired. I find this is ubiquitous with every brand of sling or alpine draw I've purchased -- albeit, some brands last longer than others. 

My question is this: does anyone know what the coating is (if it is, in fact, a type of coating)? Can it be reapplied to a sling to "bring it back life" and recover this much-desired smooth operation? 

B McG · · California · Joined Nov 2019 · Points: 1

Just throwing out a half baked idea, but maybe hitting them with an iron to soften the fuzz and smooth out the sling? 

Gunkiemike · · Unknown Hometown · Joined Jul 2009 · Points: 3,777
B McG wrote:

Just throwing out a half baked idea, but maybe hitting them with an iron to soften the fuzz and smooth out the sling? 

Run a lighter along them a couple times.

B McG · · California · Joined Nov 2019 · Points: 1
Gunkiemike wrote:

Run a lighter along them a couple times.

I thought that too but I think it using an iron would really refresh that smoothness OP is looking for.

Nigel Barry · · England · Joined Nov 2022 · Points: 5,625

Is this something like the "waterproofing" applied to ropes to pass the 90 deg granite edge fall test, which does "wear" off.

that guy named seb · · Britland · Joined Oct 2015 · Points: 241

There is no coating on dyneema slings. If your sling are tacky retire them. 

Cherokee Nunes · · Unknown Hometown · Joined May 2015 · Points: 0

I thought that too but I think it using an iron would really refresh that smoothness OP is looking for.

We do this all the time! This isn't common knowledge???

phylp phylp · · Upland · Joined May 2015 · Points: 1,152

I have never noticed this phenomenon at all. I usually keep my alpine slings for about 8 years, before retiring and replacing. But I climb almost exclusively in low humidity/ high desert environments and I live in a very low humidity environment so my house is never humid. Could this be something to do with where you live? 

Cosmic Hotdog · · California · Joined Sep 2019 · Points: 462

Michael you're not crazy, I know exactly what you mean. New dyneema slings absolutely do have a particular shine and smooth, glossy finish to them which eventually goes away over time. 

Similar to a new rope that's dry treated. They start out super smooth and they glide really well, and then the coating wears off and they get more and more fuzzy which creates more friction.

How to fix this, idk if you can but I for sure know what you mean.

Mr Rogers · · Pollock Pines and Bay area CA · Joined Aug 2010 · Points: 92
Cosmic Hotdog wrote:

Michael you're not crazy, I know exactly what you mean. New dyneema slings absolutely do have a particular shine and smooth, glossy finish to them which eventually goes away over time. 

Similar to a new rope that's dry treated. They start out super smooth and they glide really well, and then the coating wears off and they get more and more fuzzy which creates more friction.

How to fix this, idk if you can but I for sure know what you mean.

UHMWPE that gets annealed is soaked in a silicone oil bath (sometimes glycerin) and thats the slick feeling y'all are talkin' about. Its not a coating in the sense of single braids that get a UV/abraision coating that many times changes the color of the UHMWPE. But it indeed leaves a coat of it on the fibers, which as you all find, wears off.

Personally, I would not use an iron on dyneema slings. Dyneema has a SUPER low melting temp (145ºC) and can degrade at temps as low as 70-80ºC. Would it actually be an issue? prob not, but even nylon has a higher melting point at 215ºC. I woudn't do it, and I'm thoroghly super good enough type dude that is quite comfortable with pushing limits of gear.

Slim Pickens · · Unknown Hometown · Joined Mar 2023 · Points: 0

Fuzzy, yes. Tacky, that's new to me. Maybe run your slings through a wash cycle to see if that makes them less tacky—could just be accumulated dirt and skin oils.

Use a fabric shaver to de-fuzz your slings? 

Insofar as anything needs to be done at all, I wouldn't expect ironing to be effective.

phylp phylp · · Upland · Joined May 2015 · Points: 1,152
Slim Pickens wrote:

Fuzzy, yes. Tacky, that's new to me. Maybe run your slings through a wash cycle to see if that makes them less tacky—could just be accumulated dirt and skin oils.

Yeah mine may get a bit fuzzy but not at all tacky  - maybe combo of skin oil ( I have quite dry skin),  chalk ( which I don’t use) and dirt.  

Ben Zartman · · Little Compton, RI · Joined Apr 2024 · Points: 0

You could try the rope-safe coating I use for my Seamless Runners: Dragoncoat.  It comes in clear, as well as eight other colors.  While it dries a bit stiff, it loosens up quickly, but the protection lasts a long time.  We often refresh old sailing rope Dyneema tips with it as well.

https://zartmancruising.com/rigging-shop/product/rope-dye/

Michael Wolfe · · Madison, WI · Joined Oct 2021 · Points: 326
Mr Rogers wrote:

UHMWPE that gets annealed is soaked in a silicone oil bath (sometimes glycerin) and thats the slick feeling y'all are talkin' about. Its not a coating in the sense of single braids that get a UV/abraision coating that many times changes the color of the UHMWPE. But it indeed leaves a coat of it on the fibers, which as you all find, wears off.

Personally, I would not use an iron on dyneema slings. Dyneema has a SUPER low melting temp (145ºC) and can degrade at temps as low as 70-80ºC. Would it actually be an issue? prob not, but even nylon has a higher melting point at 215ºC. I woudn't do it, and I'm thoroghly super good enough type dude that is quite comfortable with pushing limits of gear.

Thanks! This is the information I was looking for. 

I echo your concern about heating up dyneema. It's interesting that the UHMWPE anneal temperatures are close to its melting points (135-138 C, taken from the wikipedia link below). Any chance you can point me to details on this recipe? If there's a way to recreate the silicone oil bath without compromising the sling's integrity and strength, that would solve the problem here! 

https://en.wikipedia.org/wiki/Ultra-high-molecular-weight_polyethylene

Jay Goodwin · · OR-NV-CA-ID-WY · Joined May 2016 · Points: 15

Might try a soak in Wet Platinum 100% silicon. It leaves things pretty slippery.

clearance clarence · · Unknown Hometown · Joined Dec 2017 · Points: 6

I have found that giving to charity helps with problems of prioritization .....

Guideline #1: Don't be a jerk.

Climbing Gear Discussion
Post a Reply to "Recovering alpine draws that deploy smoothly"

Log In to Reply
Welcome

Join the Community! It's FREE

Already have an account? Login to close this notice.