Mountain Project Logo

Routes in Tom-Tom Tower Area

Reach Around- Tommy Knocker to Tom-Tom Variation, The T 5.10 6b 20 VII- 19 E2 5b PG13
Tom-Tom Tower- North Face T 5.9 5c 17 VI 17 HVS 5a X
Tommy Knocker- South Face T 5.10 6b 20 VII- 19 E2 5b C1+
Tommy Knocker--Tomfoolery T 5.10+ 6b+ 21 VII+ 20 E3 5b
Type: Trad, Aid, 360 ft, 4 pitches, Grade III
FA: James Garret & Chris Donharl, January 2000
Page Views: 600 total, 9/month
Shared By: IanA on Apr 24, 2012
Admins: slim, Andrew Gram, Perin Blanchard, grk10vq

You & This Route


3 Opinions

Your To-Do List:

Add To-Do

Your Star Rating:


     Clear Rating

Your Difficulty Rating:


-none- Change

Your Ticks:

Add New Tick
    -none-
RAIN, WET ROCK and RAPTOR CLOSURES: The sandstone around Moab is fragile and is very easily damaged when it is wet. Also please ask and be aware of Raptor Closures in areas such as CAT WALL and RESERVOIR WALL in Indian Creek Details

Description

Pitch 1: 40m Begin on the towers south face. Climb up and right on loose rock, then up 5.9 left-facing corner. Continue angling right to a large ledge. Traverse right and build a belay at the base of a left-facing dihedral.

Pitch 2: 25m Climb up 5.9 left-facing dihedral on excellent finger jams. Pull over short rotten section and move right and build a belay below a wide crack at the saddle between Tom-Tom and Tommy Knocker.

Pitch 3: 20m Follow 4 bolt ladder with a few placements in between to a few free moves and a two bolt anchor on a ledge at the bedding seam.

Pitch 4: 29m Walk right along bedding seam and climb first groove to a 5.10 off-width to the summit. Belay off fixed anchor.

Descent: Two double rope raps. Rappel to the top of pitch 1 then to the ground.

Location

This route climbs the separated spire off a divided from the main Tom-Tom Tower. The route starts on the south face.

Protection

Standard desert rack, hooks, quickdraws,and rivet hangers.

Photos

Trevor Bowman
Sheridan, WY
 
Trevor Bowman   Sheridan, WY
 
A nice tower, but while this may have less choss than others out here, it was still pretty chossy! There was a lot of soft, exfoliating stone on several pitches, more so than I've encountered on my few VOG forays.

Rivet hangers aren't necessary on the bolt ladder anymore as I left one on the final bolt stud, but I would recommend a short stick clip to bypass the hook move. I blew out the rock around the lower and better looking hook slot as soon as I eased onto it. The higher slot will probably work for someone better at hooking than myself, but since this is basically a bolt ladder and a higher blown hook may spill you on the ledge, it will prove much easier and safer to skip it.

A big cam (#5 or #6 BD) could ease the mind on the final pitch, which is awkward and no give me. A big cam or two is necessary to protect the first pitch if you tackle the undercling/layback flake/corner depicted in the above photo...I didn't have one and simply wormed up the squeeze chimney immediately right of this, which wasn't hard and felt much more secure.

According to the register, we were the 6th party up this.

We added (with permission from James G.) a set of 1/2" stainless bolts to the belay ledge in the notch atop the 2nd pitch and added one 1/2" stainless bolt and chains to the 1st pitch anchor. The summit anchor was already a steel setup. You can now rap with a single 70m (60m should work but it will be close on the 1st and 3rd rappels) with no tat involved. Thanks to the ASCA for providing most of the hardware! Dec 2, 2014