Removing 1/2" Plated Steel Wedge Bolts
|
How do you pull 1/2" plated wedge anchors? Mostly used for anchors in Dolomite. |
|
I haven't tried to spin a 1/2" wedge yet. It will be hard on the drill clutch to be sure. I would advise knocking loose the collar and manually turning it using two nuts and a socket wrench to get it going. Report back if it works. Making a 1/2" spinner shouldn't be that difficult - Get a 1/2-20 coupling nut and cut 1/2-13 threads over the fine threads with a tap. Not ideal, but might work. |
|
Thanks Gregger. I'll let you know when I try. There's loads of em in Ten Sleep that will need to come out someday... |
|
I’d bet you’ll own an angle grinder when all is said and done. |
|
If the homemade spinner doesn't work as Greg suggests shoot me a message and I can turn a 1/2"-20 coupler for you with full 1/2"-13 threads. |
|
If you dont want to bother with the store bought fine thread adapter you can make one from worn out sds bit. Cut it off and remove some hardness by heating red hot with propane torch and let cool slowly. Then cutting threads is not too difficult. T. Fisher |
|
What solution did you end up using for removing 1/2” wedge bolts? There are a handful of old bolts here in Tulsa that are either 12mm or 1/2” wedge bolts |
|
I haven't got around to trying as the ones that need removed are covered in snow right now. I'm going to try to put together a setup similar to what Greg suggested. I think lubricating such a large bolt with water will be very important. |
|
Taylor Spiegelberg wrote: I haven't got around to trying as the ones that need removed are covered in snow right now. I'm going to try to put together a setup similar to what Greg suggested. I think lubricating such a large bolt with water will be very important. Lube and spin. Its nice to have a burly drill like my Hilti Te-6 but I've gotten them going with my little 12v milwaukee as well. The nice thing about spinning 1/2" wedge bolts is that developers, at least where I live, never torque the bolt properly so getting the clip to unseat is easy. I like the spin and funk with a rod hanger attached method. I pulled a bunch last summer, most looking like this... |
|
C. Williams wrote: it appears with what you got out that you were able to re use the hole? maybe not with another wedge bolt as they are already 1/2" Glue ins? |
|
beach wrote: Yep, I did spin a bit just to clean the hole a bit. I did drill the crux bolts to 5/8" for Jim's 8mm twist bolts. |
|
That’s rad if you can re use the hole, especially if you put in a 1/2 stainless wedge bolt. That will get you some serious time, then replace it with a mega glue in. That’s quite the lifespan from one hole. |
|
C. Williams wrote: Can you provide info on what you purchased for the 1/2" spinner tool and puller? Thread size, coupler nut size? I have the Access Fund's standard spinner tool that they've been sending out along with the puller. Thanks! |
|
This plus a short 3/8-16 piece of AllThread should do it: |
|
Gregger Man wrote: This plus a short 3/8-16 piece of AllThread should do it: Correct me if I’m wrong - that’s for the puller, but depending on the spinner you have you might need a different coupler nut for that, correct? |
|
Screw the 1/2" side of the reducer onto the 1/2" stud bolt. |
|
Gregger Man wrote: Screw the 1/2" side of the reducer onto the 1/2" stud bolt. Oh... duh. Sorry. I was first imagining replacing the coupler nut on both devices, but makes plenty of sense. Thanks! |
|
Greg beat me to it. That's the exact setup. |
|
Pulled two 1/2” wedges using just a coupler nut and 1.25” of 3/8” rod to adapt to the standard tools today. Definitely more difficult than the 3/8” wedges I’ve pulled out at the same crag. After tapping in to disengage the cone, both were difficult to start turning, even with a wrench. One continued to re-engage as I pulled it with the Hurley, so I wiggled it up and down a bit and it eventually pulled using the Hurley, but without the clip which stayed in the hole. The other one pulled fully. One or two unsuccessful pulling attempts with the Hurley, followed by more spinning in between, and it finally pulled. Thanks for the tips everyone |
|
Those things dont look so bad... always loved the burl factor of 1/2 studs. |
|
Rob warden The space lizard wrote: Those things dont look so bad... always loved the burl factor of 1/2 studs. Agreed, they look better than I expected them to. Since spinning them slightly widened the hole, the hole was drilled out to a 5/8” hole and they were replaced with large twist bolts (based on ASCA recommendation) |